EUC Mobile Event Speaker Setup/Break Down Documentation
One Speaker + One-Two Microphones
Setup:
-
Step 0: (If the event is longer than 3 hours long) Plug power cable into speaker.
-
Please note that the transmitter only has a 3 hour battery life.
-
-
Step 1: Turn on LTG Speaker 1.
-
Step 2: Pop out Transmitter 1.
-
Step 3: Turn on the Transmitter 1. The blue light will turn on when done correctly.
-
Step 4: Plug Transmitter 1 into bottom of LTG microphone 1.
-
Step 5: If you wish to have a second microphone, follow steps 2-4 again but with Transmitter 2 and LTG Microphone 2.
-
Step 6: Adjust the volume to your liking.
-
Note: Each Microphone will have its own volume.
-
Break Down:
-
Step 1: Power off transmitter(s).
-
Step 2: Unplug transmitter(s) from microphone(s).
-
Step 3: Plug transmitter(s) back into speaker.
-
Step 4: Turn off speaker.
Two Speakers + One-Two Microphones
Setup:
-
Step 0: (If the event is longer than 3 hours long) Plug power cable into speaker.
-
Please note that the transmitter only has a 3 hour battery life.
-
-
Step 1: Pop Transmitter 1 out of LTG Speaker 1 by pushing the transmitter in, then letting it pop out enough to remove it.
-
Step 2: Turn on the Transmitter 1.
-
Step 3: Plug Transmitter 1 into the port under “Line Out” on LTG Speaker 2.
-
Step 4: Pop Transmitter 3 out of LTG Speak 2.
-
Step 5: Turn on the Transmitter 3.
-
Step 6: Plug Transmitter 3 into LTG Microphone 1.
-
Step 7: If you would like two microphones repeat steps 4-6 with Transmitter 4 and Microphone 2.
-
Step 8: Adjust the volume to your liking.
-
Note: Each Microphone will have its own volume.
-
Break Down:
-
Step 1: Power off transmitter(s).
-
Step 2: Unplug transmitter(s) from microphone(s).
-
Step 3: Plug transmitter(s) back into speaker.
-
Step 4: Turn off speaker.
Two Speakers + Three Microphones (See Notes)
Please note that two microphones sounds will come out of both speakers. But the third microphone will only come out of one speaker.
Setup:
-
Step 0: (If the event is longer than 3 hours long) Plug power cable into speaker.
-
Please note that the transmitter only has a 3 hour battery life.
-
-
Step 1: Turn on both LTG Speakers.
-
Step 2: Plug the XLR cable into the speakers.
-
XLR Side 1 goes into the “Line Out” port on LTG Speaker 1.
-
XLR Side2 goes into the second input port next to LTG Transmitter 4 on LTG Speaker 2.
-
-
Step 3: On LTG Speaker 1, pop out Transmitter 1 and 2.
-
Step 4: Turn on both transmitters.
-
Step 5: Plug transmitters into the bottom of LTG Microphone 1 and 2.
-
Step 6: On LTG Speaker 2, pop out LTG Transmitter 3.
-
Step 7: Turn on LTG Transmitter 3.
-
Step 8: Plug LTG Transmitter 3 into LTG Microphone 3.
-
Step 9: Adjust the volume to your liking.
-
Note: Each Microphone will have its own volume.
-
Break Down:
-
Step 1: Power off transmitter(s).
-
Step 2: Unplug transmitter(s) from microphone(s).
-
Step 3: Plug transmitter(s) back into speaker.
-
Step 4: Turn off speaker.