Remote Desktop access to Waisman computers
General overview
Remotely accessing a Waisman computer involves first using a VPN to tunnel your internet traffic through UW-Madison, then connecting to the particular computer at Waisman.
Step 0: One-time setup on your personal computer
Install the VPN, Palo Alto Global Protect
-
Go to https://uwmadison.vpn.wisc.edu/ and log in with your NetID and password
-
For Mac users, click to download the Mac 32/64 bit option. For Windows users, click to download the Windows 64 bit option
-
Once downloaded, install it.
-
Once installed, it should be a little grey globe icon in your toolbar (Windows: bottom right corner; Mac: top right corner). Click on the globe.
-
When asked for portal address, enter uwmadison.vpn.wisc.edu
For more in-depth directions, see these pages: Mac or Windows.
Install remote desktop software
If your personal computer is a Windows PC, this program is installed by default. Skip to the next section.
If your personal computer is a Mac:
- Open the App Store
- Search for "Windows App"
- Install it
Step 1: Connect to the VPN
- Launch the app Palo Alto Global Protect. If the grey globe icon is in your toolbar, that means it's already running -- just click the globe icon.
- Set the portal to
uwmadison.vpn.wisc.edu, then click Connect. - Enter your NetID username and password. It will prompt you to do dual factor authentication.
- When the globe turns blue and green, you are connected. All your internet traffic is now being routed through UW-Madison.
Step 2: Connect to a Waisman Computer with Remote Desktop
Based on the operating system of your personal computer, expand the appropriate section below and perform those steps.
Windows instructions
In the Computer field, enter the name of the computer you're connecting to (see list at the very bottom of this KB). In the User name field, enter yourNetIDHere@ad.wisc.edu, for example, bbadger@ad.wisc.edu.
- If that doesn't work, try ad\NetIDusername. For example, ad\bbadger. Note that the slash between "ad" and your NetID is a backslash, not a forward slash.
Click Connect at the bottom right. In the Enter Your Credentials popup, enter yourNetIDUsername@ad.wisc.edu and your NetID password. Click OK.
Mac instructions
-
Open "Windows App"
-
The first time you open it, you will need to add a PC to log in to
- In the top right, click the + icon --> Add PC
- In the pop-up window, for PC name, type in the name of the Waisman computer you want to connect to. (At the very bottom of this KB doc, there's a section that lists all the Waisman computer names)
- In the Friendly Name field, put the first part of the computer name
- Leave everything else as is

-
Click Add at the bottom of the pop-up window
-
Back on the main screen, double-click on the computer you just added
-
Log in with your NetID username and NetID password
- If that doesn't work, try setting your username to [username]@ad.wisc.edu. For example, bbadger@ad.wisc.edu
- If THAT doesn't work, try putting ad\ before your username, like in the picture below. For example, ad\bbadger. Note that the slash between 'ad' and your NetID is a backslash, not a forward slash.

When you're done working a remote session, close out properly
- Sign out of the Waisman computer.
- Click the Windows icon in the bottom toolbar
- Click your profile picture
- Choose "sign out". After a few seconds, the remote session should close and/or the screen will go blank
- Disconnect from the VPN
- Back on your local computer, click the Global Protect icon (the globe)
- Click Disconnect
Waisman computer names
- [name], for example, quiberon
- wit-[name], for example, wit-quiberon
- [name].waisman.wisc.edu, for example, quiberon.waisman.wisc.edu
- wit-[name].waisman.wisc.edu, for example, wit-quiberon.waisman.wisc.edu
You will just need to try one and see if it works. Theoretically wit-[name] is the only "correct" format, so try that first, but in practice it depends.
Mac 0x3707 error
These instructions are mainly for Chris but you can try if you run into this error from your Mac personal laptop.
- In Windows App, go to Settings >> Credentials. Clear any credentials with your NetID username and password
- In the Saved Devices list, choose Configure the computer you want to connect to. Change the device name to wit-[name].
- Try to connect to the device
- If it DOES connect to the device (ie, if it prompts you for a username and password), skip to step #9
- If it DOES NOT connect (ie, if it says "device not found" or otherwise doesn't show a login prompt), continue to step #4
- Open the program Terminal
- Enter ping wit-[computer name].waisman.wisc.edu, for example,
ping wit-quiberon.waisman.wisc.edu. Make note of the IP address. - Enter sudo nano /etc/hosts
- Add the IP address of the computer from step #5, following the format in the document. Hit ^ X to exit, type Y to save, then Enter to save to /etc/hosts . You're done in Terminal.
- Back in Windows App, try connecting to the device again by double clicking it. It should now present a login prompt (username and password).
- Enter your login credentials
- For your username, use [netID username]@ad.wisc.edu. Theoretically username@ad.wisc.edu is the most correct format, instead of ad\username.
- For your password, enter your NetID password
If that doesn't work, contact Chris to try and help.